3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? 2-fb power header 2 mm 4/5-row, vertical, press-fit tail mp2 series physical electrical environmental metpak is a trademark of 3m company. futurebus+ is a registered trademark of the institute of electrical and electronic engineers, inc. (ieee) insulation material: high temp lcp flammability: ul 94v-0 color: beige contact material: copper alloy plating underplating: 50 " [1.27 m] nickel wiping area: see ordering information tails: see ordering information current rating: power: 6.50 a per power socket contact at 70 c insulation resistance: 10 3 m withstanding voltage: 1000 v ac temperature rating: -55 c to +125 c ts-1126-06 sheet 1 of 4 date modified: april 11, 2007 ? 6.50 amps per contact ? early mate late break (emlb) for hot swap or selective loading options ? end-to-end stackable ? optional feed-through tail (press-fit) ? futurebus+? compatible ? see regulatory information (ria) for chemical compliance information ul file no: e68080
3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? 2-fb power header 2 mm 4/5-row, vertical, press-fit tail mp2 series ts-1126-06 sheet 2 of 4 mp2 - hpxx - xxp1 - xxxxx ordering information power header contact count (see table 1) rows 4 = 4 rows 5 = 5 rows tail length (see table 3) termination style p = press-fit plating options: (see table 4) loading pattern (see table 2) position 2 for special monoblocks and pin arrangements contact 3m sales representative 15.80 .622 11.50 .453 1.40 .055 2.00 .079 3x 4 row product 17.00 .669 3.50 .138 position 1 12.00 .472 only present on solder tail product 11.95 .470 6.00 .236 solder tail product row 17.80 .701 13.52 .532 "b" mating length "a" tail length c d e a b press-fit product rear plug-up 5 row product press-fit product 10.00 .394 11.95 .470 0 0.0 0.00 mm 3 0.3 0.13 mm [inch] tolerance unless noted [ ] dimensions for reference only note: 1. refer to iec 61076-4-104 futurebus+? global standard. 2. "press fit" describes a contact tail having a compliant section designed to make a reliable electrical connection with a plated through-hole (pth) in a printed circuit board, typically a "back plane.?
3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? 2-fb power header 2 mm 4/5-row, vertical, press-fit tail mp2 series ts-1126-06 sheet 3 of 4 contact count no of rows 08 4 10 5 table 1 4.60 [0.181] *compliant-pin tail press-fit tail termination option no. 1 table 3- tail length dim. "a" loading pattern code description 1 all positions fille d 6.50 [0.256] 6.50 [0.256] 6.50 [0 .256] 6.50 [0.256] 6.50 [0.256] 2 all positions fille d 8.00 [0.315] 8.00 [0.315] 7.25 [0 .285] 6.50 [0.256] 6.50 [0.256] 3 all positions fille d 6.50 [0.256] 8.00 [0.315] 6.50 [0 .256] 6.50 [0.256] 6.50 [0.256] 4 all positions fille d 6.50 [0.256] 7.25 [0.285] 7.25 [0 .285] 8.00 [0.315] 8.00 [0.315] 5 all positions fille d 7.25 [0.285] 8.00 [0.315] 7.25 [0 .285] 6.50 [0.256] 6.50 [0.256] 6 all positions fille d 8.00 [0.315] 8.00 [0.315] 8.00 [0 .315] 8.00 [0.315] 8.00 [0.315] 7 all positions fille d 7.25 [0.285] 7.25 [0.285] 7.25 [0 .285] 7.25 [0.285] 7.25 [0.285] 8 all positions fille d 8.00 [0.315] 6.50 [0.256] 8.00 [0 .315] 7.25 [0.285] 7.25 [0.285] 9 all positions fille d 8.00 [0.315] 7.25 [0.285] 6.50 [0 .256] 6.50 [0.256] 6.50 [0.256] a all positions fille d 8.00 [0.315] 8.00 [0.315] 7.25 [0 .285] 7.25 [0.285] 7.25 [0.285] c all positions fille d 8.00 [0.315] 8.00 [0.315] 8.00 [0 .315] 6.50 [0.256] 6.50 [0.256] d all positions fille d 8.00 [0.315] 6.50 [0.256] 6.50 [0 .256] 6.50 [0.256] 6.50 [0.256] g all positions fille d 8.00 [0.315] 8.00 [0.315] 8.00 [0 .315] 8.00 [0.315] 5.75 [0.226] h all positions fille d 8.00 [0.315] 8.00 [0.315] 7.25 [0 .285] 8.00 [0.315] 8.00 [0.315] table 2- mate length mate length row a mate length row b mate length row c mate length row d mate length row e (5-row prod. only) plating suffix plating composition pl ating suffix plating composition 0.25 m [10 "] min. au contact area 0.25 m [10 "] min. au contact area 2.54 m [100 "] min. snpb tail area 5.08 m [200 "] min. matt whisker mitigating sn tail area 1.27 m [50 "] min. ni all over 1.27 m [50 "] min. ni all over 0.76 m [30 "] min. au contact area 0.76 m [30 "] min. au contact area 2.54 m [100 "] min. snpb tail area 5.08 m [200 "] min. matt whisker mitigating sn tail area 1.27 m [50 "] min. ni all over 1.27 m [50 "] min. ni all over 0.08 m [3 "] min. au contact area 1.27 m [50 "] min. au contact area, lubricated 0.67 m [27 "] min. pdni contact area 5.08 m [200 "] min. matt whisker mitigating sn tail area 2.54 m [100 "] min. snpb tail area 1.27 m [50 "] min. ni all over 1.27 m [50 "] min. ni all over 0.08 m [3 "] min. au contact area 0.13 m [5 "] min. hard au contact area, lubricated 0.67 m [27 "] min. pdni contact area 1.02 m [40 "] min. pdni contact area 5.08 m [200 "] min. matt whisker mitigating sn tail area 0.10 m [4 "] min. pd contact area 1.27 m [50 "] min. ni all over 2.54 m [100 "] min. snpb tail area 0.13 m [5 "] min. hard au contact area, lubricated 1.27 m [50 "] min. ni all over 1.02 m [40 "] min. pdni contact area 0.10 m [4 "] min. pd contact area 5.08 m [200 "] min. matt whisker mitigating sn tail area 1.27 m [50 "] min. ni all over pd (ria e1 & c1 apply) table 4 - plating rf (ria e1 & c1 apply) lr (ria e1 & c1 apply) fj (ria e1 & c1 apply ) kr (ria e1 & c1 apply) tg (ria e2 & c2 apply) tg30 (ria e2 & c2 apply) tr30 (ria e2 & c2 apply) tr40b (ria e2 & c2 apply)
3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? 2-fb power header 2 mm 4/5-row, vertical, press-fit tail mp2 series ts-1126-06 sheet 4 of 4 "d" plated thru hole recommended 4 row press-fit pcb hole mounting pattern lo 0.10 a1 6.00 .236 2.00 .079 3x 10.00 .394 16.00 .630 min. 2.00 .079 5x recommended 5 row press-fit pcb hole mounting pattern 2.00 .079 4x "d" plated thru hole lo 0.10 a1 10.00 .394 8.00 .315 18.00 .709 min. 2.00 .079 5x hole finished dia. mm [in] cu thickness mm [in] snpb thickness microns ["] drilled hole dia. mm [in] "d" 0.65-0.80 [.0256-.0315] 0.025 [.001] min 15 [600] max 0.81-0.86 [.0319-.0339] table 5 -- hole plating for tg, tg30, tr30, tr40b finishes only hole finished dia. mm [in] cu thickness mm [in] immersion matte sn thickness microns ["] electrolitic au thickness microns ["] osp entek thickness microns ["] drilled hole dia. mm [in] 0.700-0.800 0.025-0.045 0.5 - 2.5 0.1 - 0.5 0.2 - 0.5 0.830-0.860 [.0330-.0340] or [.0276-.0315] [0.001-0.002] [20 - 100] [4 - 20] [8 - 20] 0.85mm [ #66] twist drill table 6 -- hole plating for fj, kr, rf, lr, and pd finishes only "d"
regulatory information appendix 3m electronic solutions division/interconnect europe appendix e1: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product is rohs compliant 2005/95/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e2: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/747/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e3: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment as amended by commission decision 2005/618/ec. this product contains lead in the solder tail area in excess of the maximum concentration value allowed. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e4: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains decabde in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/17/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. ria-2217-a
china appendix c1: china rohs electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix c2: china rohs 2 0 electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. the numerical reference in the symbol above should not be construed as a representation regarding the products life or an extension of a product warranty. the product warranty is stated below. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the product warranty stated below. important notice all statements, technical information, and recommendations related to 3ms products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. before using this product, you must evaluate it and determine if it is suitable for your intended application. you assume all risks and liability associated with such use. any statements related to the product which are not contained in 3ms current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3m. warranty; limited remedy; limited liability. this product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3m makes no other warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. if this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3ms option, to replace or repair the 3m product or refund the purchase price of the 3m product. except where prohibited by law, 3m will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3m product, regardless of the legal theory asserted. name and content of hazardous substances or elements 3 electronic solutions division 6801 river place blvd. austin, tx 78726-9000 800/225-5373 www.3m.com/interconnects ria-2217-a ? 3m 2007
|
